CASASCAPES
3 IN 1 CLEANER

3 IN 1 CLEANER

Technical Data Sheet

Sealer Prep

Before sealing, use 3 IN 1 Cleaner. A cleaned surface is a critical step before a sealer is applied.

The sealer will be able to penetrate more deeply into the pores.

 

Efflorescence Cleaner

Removes efflorescence from the surface of concrete pavers and natural stones

  • No hydrochloric acid in product
  • Washes off with water

Shampoo

  • Removes penetrated dirt
  • Restores the pavers to its natural color
  • No muriatic acid in product
  • Washes off with water

Sprayer

  • Easy to use, provides an accurate water-to-cleaner mix.
  • CasaScapes Sprayer connects directly to your garden hose.
  • Use 3 in 1 Cleaner
  • Adjustable sprayer to premix 4 or 8 parts water with 1 part 3 IN 1 Cleaner.
  • Safe to use
  • Clean, mess- free work.

APPLICATION FOR 3 IN 1 EFFLORESCENCE

See videos for visual installation. Always refer to the latest CasaScapes 3 in 1
Technical Data Sheet (TDS) at CasaScapes.com before installation.

Wet paver surface with water.

Dip a hard bristle brush in a pail containing the diluted product or use a pump sprayer to apply on the paver surface and scrub. 1 U.S. gal. (3.78 L.) of diluted product is to be used for every 40 sq. ft. (3.7 sq. m.) of paver surface.

Rinse thoroughly with water and move on to the next section of 40 sq. ft. (3.7 sq. m.).

Repeat steps 2 & 3 over all the sections in question.

Once the surface is clean, use water hose and generously rinse off Casascapes Efflorescence Cleaner until there is no more foaming action on the pavers.

  • 3 IN 1 Cleaner should be used prior to applying a sealer to ensure a proper sealer adhesion.
  • Freshly installed Polymeric Sand must be allowed to cure for 48 hours at above 59°F (15°C) and no rain before using 3 IN 1 Cleaner.
  • Do not let product dry up on paver surface.
  • Wear goggles and rubber gloves.
  • Never use on new concrete pavers. Wait at least 60 days after new pavers are installed before using this product.
  • ALWAYS TEST the product on a small hidden area of approximately 4 sq. ft. (0.4 sq. m.) to ensure the results will meet your expectations. Do not apply under extremely strong sun.
  • Dilute to 4 parts water, 1 part 3 IN 1 Cleaner concentrated liquid, any concentration greater than this can discolor the pavers.

4 parts water 1 part product. Always test the dilution on a small area before applying.

You might have to redo it again if there is a lot of efflorescence trapped in the pavers.
* Pavers should only be sealed 60 days after the installation date.
* Please store container at above 32°F (0°C).

APPLICATION FOR 3 IN 1 SHAMPOO

See videos for visual installation. Always refer to the latest CasaScapes Stone Dust
Technical Data Sheet (TDS) at CasaScapes.com before installation.

Wet paver surface with water.

Dip a hard bristle brush in a pail containing the mixed product, apply on the paver surface and scrub. One quart (liter) of mixed product is to be used for every 20 sq. ft of paver surface.

Rinse thoroughly with water and move on to the next section of 20 sq. ft.

Repeat steps 2 & 3 over all the sections in question.

Once the surface is clean, use water hose and generously rinse off CasaScapes Shampoo until there is no more foaming action on the pavers.

  • Contact your paver manufacturer to validate the required period before using any cleaning agent on their product.
  • This product is not an efflorescence cleaner.
  • Do not let product dry up on surface.
  • Wear goggles and rubber gloves.
  • Mix 4 parts water, 1 part CasaScapes Shampoo concentrated liquid, any concentration greater than this can discolor the pavers.
  • Do not apply under hot sun.
  • Keep paver surface wet from start to finish.

4 parts water 1 part product.

Repeat steps if there is a lot of dirt trapped in the pavers and natural stones.